16-Channel Servo Driver

16-Channel Servo Driver

Features:

  • Driver IC: PCA9685
  • Voltage Range – Input: 3V to 5V
  • Max. Supply Voltage: 6V
  • Frequency(Fast-mode 12C-bus): 40-1000Hz
  • Channel number: 16 channel.
  • Resolution: 12 bit
  • 6 hardware address pins allow 62 PCA9685 devices to be connected to the same I2C-bus



L298 Motor driver

Product Name : Motor Driver
Model : L298
Motor supply: 6 to 35 VDC
Control Logic: Standard TTL Logic Level
Output Power: Up to 2A each
Enable and Direction Control Pins
Heat sink for IC
Power-On LED indicator
4 Direction LED indicators

 




Motor Shield V2

Motor Shield V2 to Control 4 DC Motor or 2 Stepper and Servo

Motor Stepper Servo Robot Shield v2 with PWM Driver Shield For Arduino

  • 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer – no jitter!
  • 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A for brief 20ms peaks) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.
  • Motors automatically disabled on power-up
  • Big terminal block connectors to easily hook up wires (18-26AWG) and power
  • Arduino reset button brought up top
  • Polarity protected 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
  • Tested compatible with Arduino UNO, Leonardo, ADK/Mega R3, Due, Diecimila & Duemilanove. Works with Mega/ADK R2 and earlier with 2 wire jumpers.



Stepper Motor Driver

The A4988 stepper motor driver carrier is a breakout board for Allegro’s easy-to-use A4988 microstepping bipolar stepper motor driver and is a drop-in replacement for the A4983 stepper motor driver carrier

: Features

Product name : stepper motor driver
Model : A4988
Voltage : 8-35 V
Current : 2 A
Adjustable current limiting
Overcurrent protection

شريحة  متكامله تُستخدممع المحرك الخطوى  التي لا تستطيع المتحكمات الدقيقة او دوائر التحكم الاخري قيادتها مباشرة ، فهذه الشريحة تُستخدم لربط دوائر التحكم مع المحرك الخطوى

 المميزات :

مصدر الجهد : 8-35 فولت
التيار : 2 امبير
يمكن التحكم في التيار
حماية التيار الزائد




Stepper Motor Driver Tb6600

Stepper Motor Driver Tb6600

Features:

  • Model No.: TB6600,
  • Supply Voltage: 9VDC – 42VDC,
  • Current: 0.5A – 4.0A,
  • Usage: Bipolar Stepper Motor Driver



VNH2SP30 DC Motor Driver

VNH2SP30 DC Motor Driver

Features:

  • Voltage max: 16V
  • Maximum Output current: 30 A
  • Practical Continuous Current: 14 A
  • Current sensing available to Arduino analog pin
  • MOSFET on-resistance: 19 mΩ (per leg)
  • Maximum PWM frequency: 20 kHz
  • Thermal Shutdown
  •  Under voltage and Over voltage shutdown